Essential Plumbing Insights for Installing a Bathtub
Essential Plumbing Insights for Installing a Bathtub
Blog Article
Are you in search of help around A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a new one is likewise a moderately tough task. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall to remove the old tub and place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require an assistant to move out the old tub and also set in the new one. See to it you have qualified on your own for the work as well as fit trying it. Rather than employing a service provider to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This article will assist you mount a new tub in your shower room if you have actually currently bought a new tub as well as don't need to transform the setup of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the bathtub up until the level reads level.
To set up taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the same for the other tap.
Turn on the supply of water and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Load the tub as well as also check the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub should wait till the bath tub has been used at the very least once as this will certainly settle it right into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bath needs to be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last setting.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture relatively early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very curious about A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked the new article. If you please set aside a second to share this content if you enjoyed it. Thanks a lot for your time spent reading it.
Go Deal Report this page